Search

Roof & Foundation Coatings

View as Grid List
Sort by
Display per page

Snow Roof Elasto-Seal 5 Gal. Roof Primer

SKU: 112011
UPC: 00016904100050
High-strength liquid rubber undercoat used with Snow Roof. Water-base, 100% elastic, resistant to standing water. Waterproofs most any roof, wall, or deck. Light gray. 1 year warranty.
$139.99

Premier 1 Gal. Non-Fibered Asphalt Roof Coating

SKU: 103612
UPC: 00047943032101
An excellent material for resurfacing flat asphalt, metal, or composition roofs. High quality asphalt base dries to a tough, flexible, weather resistant film. Recommended for resurfacing and rejuvenating old, worn out flat asphalt roofs. All roof surfaces to be coated must be dry and swept clean from grease, oil, rust, scale, loose paint, and dirt. Repair holes and tears with roof cement and suitable patching fabric. Apply by brush or appropriate spray equipment. Coverage is approximately 75 Sq. Ft. per Gal. depending on textures and porosity of surface. Use on low slope asphalt roofs (do not use on roof slopes greater that 1/2 In. per Ft.), composition roofs, or metal roofs. Do not apply over damp or wet surfaces. Limited 12 month warranty.
$14.79

Premier 1 Gal. Fibered Asphalt Roof Coating

SKU: 103587
UPC: 00047943132139
Heavy bodied fibered asphalt coating is reinforced with mineral fillers. Coating cures to a tough, flexible, weather resistant film. Excellent adhesion to asphaltic, metal, and masonry roof surfaces. Resists damage which may result from minor expansion and contraction caused by weather, temperature variation, and normal building vibration. Recommended for resurfacing and rejuvenating old, worn roofs. Coverage is approximately 1.5 to 2 Gal. per 100 Sq. Ft. Coverage depends on texture and porosity of surface. All surfaces to be coated must be dry and swept or brushed clean from grease, oil, rust, scale, loose paint, and dirt. Patch holes and tears with roof cement and suitable patching fabric. Apply by brush or spray equipment. Allow to dry thoroughly (minimum 48 hours) between coats. Do not apply over damp or wet surfaces. Limited 12 month warranty.
$13.99

Premier 1 Gal. Fibered Aluminum Roof Coating

SKU: 103747
UPC: 00047943332270
Highly reflective roof coating reduces roof surface temperature and prolongs life of roof. Forms a longer lasting bright aluminum finish. Reduces interior temperatures in summer. Use on prepared roll roofing, asphalt built-up roofs, weathered, galvanized iron and tin. Apply to dry surface only. Apply with good quality soft bristle brush, long-napped roller, or commercial grade spray equipment. Apply liberally, brushing in 1 direction only. Do not overlap. Over-brushing will interfere with leafing action of aluminum. Coverage is 1 to 1.2 Gal. per 100 Sq. Ft. Application rate may vary according to the type, age, and condition of the surface. Aluminum paste meets ASTM D-2824 Type 3.
$21.49

Premier 525 1 Gal. Mobile Home Aluminum Roof Coating

SKU: 101366
UPC: 00047943332294
Specially formulated for use on mobile home roofs. Reflects suns heat, reduces interior temperatures in summer. Keeps winter warmth inside. Forms a tough, reflective surface that repairs as it protects. May be used on prepared roll roofing, weathered galvanized iron, tin, and cinderblock. Seals hairline cracks and pinholes to increase the water resistance of the roof. Coverage is approximately 50 to 75 Sq. Ft. per Gal. depending on texture and porosity of surface. Mix thoroughly before and during use. Apply to a dry surface. Application to a damp surface will cause this product to appear brown. Apply with a roof brush, paint brush, or long-nap roller. Spread in 1 direction only. Over brushing will interfere with the leafing action of the aluminum. Limited 12 month warranty.
$22.49

Kool Seal 5 Gal. Premium 10-Year White Acrylic Elastomeric Roof Coating

SKU: 116955
UPC: 00050926002077
Formulated with 100% acrylic elastomeric resin. The coating forms a thick rubber-like blanket of protection that expands and contracts with roofs. It remains flexible from -30 deg. F. to 160 deg. F. for long-lasting protection and provides superior reflectivity to lower interior temperatures and save energy. Designed to be durable in any climate. Helps absorb sound. Higher solids for better coverage. Environmentally compliant. Recommended for metal, concrete, urethane and polystyrene foam, brick, flat and barrel cement tiles, and aged aluminum coatings. You must use Kool Seal Kool-Lastik Primer, model No. 34-600, if applying to the following surfaces: Built-up roofs, modified bitumen, bonded tar and gravel, rolled roofing, most other asphaltic surfaces, and in ponding water situations. Cured elastomeric film is mildew and algae-resistant. For use on a properly drained roof. Soap and water clean up - while wet. Reflects 90% + of the sun's rays and has energy savings up to 35%.
$119.99

Kool Seal 1 Gal. Premium 10-Year White Acrylic Elastomeric Roof Coating

SKU: 116947
UPC: 00050926002084
Formulated with 100% acrylic elastomeric resin. The coating forms a thick rubber-like blanket of protection that expands and contracts with roofs. It remains flexible from -30 deg. F. to 160 deg. F. for long-lasting protection and provides superior reflectivity to lower interior temperatures and save energy. Designed to be durable in any climate. Helps absorb sound. Higher solids for better coverage. Environmentally compliant. Recommended for metal, concrete, urethane and polystyrene foam, brick, flat and barrel cement tiles, and aged aluminum coatings. You must use Kool Seal Kool-Lastik Primer, model No. 34-600, if applying to the following surfaces: Built-up roofs, modified bitumen, bonded tar and gravel, rolled roofing, most other asphaltic surfaces, and in ponding water situations. Cured elastomeric film is mildew and algae-resistant. For use on a properly drained roof. Soap and water clean up - while wet. Reflects 90% + of the sun's rays and has energy savings up to 35%.
$35.99

Kool Seal 5 Gal. 7-Year White Acrylic Elastomeric Roof Coating

SKU: 105512
UPC: 00050926002114
Formulated with 100% acrylic elastomeric resin. The coating forms a thick rubber-like blanket of protection that expands and contracts with roofs. It remains flexible from -30 deg. F. to 160 deg. F. for long-lasting protection and provides superior reflectivity to lower interior temperatures and save energy. Recommended for metal, concrete, foam, brick, flat and barrel cement tiles, and aged aluminum coatings. You must use Kool Seal Kool-Lastik Primer, model No. 34-600, if applying to the following surfaces: Built-up roofs, modified bitumen, bonded tar and gravel, rolled roofing, most other asphaltic surfaces, and in ponding water situations. Cured elastomeric film is mildew and algae-resistant. Soap and water clean up - while wet. Reflects 90% + of the sun's rays and has energy savings up to 35%. Coverage: 80 to 100 sq. ft. per gallon, depending on surface. For use on a properly drained roof. Color: White. 7 year warranty.
$99.99

Kool Seal 1 Gal. 7-Year White Acrylic Elastomeric Roof Coating

SKU: 105511
UPC: 00050926002121
Formulated with 100% acrylic elastomeric resin. The coating forms a thick rubber-like blanket of protection that expands and contracts with roofs. It remains flexible from -30 deg. F. to 160 deg. F. for long-lasting protection and provides superior reflectivity to lower interior temperatures and save energy. Recommended for metal, concrete, foam, brick, flat and barrel cement tiles, and aged aluminum coatings. You must use Kool Seal Kool-Lastik Primer, model No. 34-600, if applying to the following surfaces: Built-up roofs, modified bitumen, bonded tar and gravel, rolled roofing, most other asphaltic surfaces, and in ponding water situations. Cured elastomeric film is mildew and algae-resistant. Soap and water clean up - while wet. Reflects 90% + of the sun's rays and has energy savings up to 35%. Coverage: 80 to 100 sq. ft. per gallon, depending on surface. For use on a properly drained roof. Color: White. 7 year warranty.
$33.99

Kool Seal 5 Gal. Acrylic Elastomeric Roof Coating

SKU: 105521
UPC: 00050926002138
Formulated with 100% acrylic elastomeric resin. The coating forms a thick rubber-like blanket of protection that expands and contracts with roofs. It provides superior reflectivity to lower interior temperatures and save energy. Recommended for metal, concrete, urethane and polystyrene foam, brick, flat and barrel cement tiles, and aged aluminum coatings. You must use Kool Seal Kool-Lastik Primer, model No. 34-600, if applying to the following surfaces: Built-up roofs, modified bitumen, bonded tar and gravel, rolled roofing, most other asphaltic surfaces, and in ponding water situations. Cured elastomeric film is mildew and algae-resistant. For use on a properly drained roof. Soap and water clean up - while wet. Reflects 90% + of the sun's rays and has energy savings up to 35%. Coverage: 80 to 100 sq. ft. per gallon, depending on surface.
$84.99

Kool Seal Kool-Lastik 5 Gal. Roof Primer

SKU: 113034
UPC: 00050926002145
Formulated with specialized acrylic latex polymer that forms an elastomeric sealant. It is designed to perform on troublesome roof surfaces and ponded water situations. It is recommended for use on rolled roofing, bonded tar and gravel, modified bitumen, built-up roofs, and most asphaltic roof surfaces. It is not required or recommended for metal or coated metal roofs. This product is a heavy-duty rubberized undercoating primer and must be topcoated. Primer is light blue in color and designed to improve adhesion of elastomeric roof coatings on troublesome surfaces and prevent leaks. It expands and contracts with your roof. Can be used as a base to convert black asphalt to white. Soap and water clean up - while wet. Do not use on roofs with a slope of 1/2" or less per foot .
$139.99

Kool Seal 1 Gal. Fibered Aluminum Roof Coating

SKU: 106895
UPC: 00050926002268
Non-asbestos reinforcing fibers bind with an asphalt blend that provides a durable roof coating. Protects roofs from the sun's damaging ultraviolet rays. Coverage: 50 to 75 Sq. Ft. per Gal. Use on: Metal, built-up roof, modified bitumen, black asphalt, rolled roofing, felts, and other aluminum asphalt based coating.
$22.49

Kool Seal Blu2White 5 Gal. Acrylic Elastomeric Roof Coating

SKU: 788063
UPC: 00050926004507
Blu2White roof coating is a color-changing acrylic finish coat that provides a highly reflective finish to lower interior temperatures and reduce energy costs. Formulated with SnowRoof technology for easy coverage, coating is blue in color during application and will transition to bright white with sun exposure. Excellent waterproofing capabilities. Resists cracking and peeling. No primer needed.
$139.99

Kool Seal Blu2White 1 Gal. Acrylic Elastomeric Roof Coating

SKU: 774395
UPC: 00050926004514
Blu2White roof coating is a color-changing acrylic finish coat that provides a highly reflective finish to lower interior temperatures and reduce energy costs. Formulated with SnowRoof technology for easy coverage, coating is blue in color during application and will transition to bright white with sun exposure. Excellent waterproofing capabilities. Resists cracking and peeling. No primer needed.
$35.49

Henry Enviro-White 1 Gal. Acrylic Elastomeric Roof Coating

SKU: 109821
UPC: 00081725032576
Enviro White Premium White Roof Coating is a premium, high-solids, white elastomeric roof coating formulated with acrylic polymers, resins, fillers, and titanium dioxide pigments. DPR (dirt pick-up resistant) technology prevents dirt and dust build-up, keeping your roof whiter and more reflective longer. This maximizes your energy savings over time. The elongation, peel strength, and solar reflectance values of this coating offer weather protection, high solar reflectivity, and superior longevity when compared to economy grade reflective roof coatings. Intact cured coating forms a permeable membrane which prevents liquid infiltration, but allows moisture vapor to vent, or breathe, out of underlying substrate. No primer needed on most new roofs or roofs in excellent condition. Older roofs in fair condition may need primer. For use on a properly drained roof. On smooth surfaces, approximately 2 gallon per 100 sq. ft. On mineral surfaces approximately 2 to 3 gallons per 100 sq. ft. Color: White. Meets the ENERGY STAR guidelines for energy efficiency. 12 year limited warranty.
$42.49

Henry Dura-Brite 1 Gal. White Acrylic Elastomeric Roof Coating

SKU: 123919
UPC: 00081725043350
A premium, high solids, white elastomeric roof coating. The elongation, peel strength and solar reflectance values of this coating offer weather protection, high solar reflectivity and superior longevity when compared to economy grade reflective roof coatings. Cured coating forms a permeable membrane which prevents liquid infiltration, but allows moisture vapor to vent, or breathe out of underlying substrate. Ponding water-resistant. Energy efficient - releases 91% of the sun's heat (thermal emittance). Elastomeric - expands and contracts without cracking. No primer needed on new roofs or roofs in excellent condition. Older roofs in fair condition may need primer. White roof coating offers a premium system which can be used over: Well adhered, weathered, previously coated white or aluminum roof surfaces, mineral surface cap sheet (conventional, SBS, or APP), smooth surface BUR, SBS, and APP roofs (require a base coat of Henry Asphalt Emulsion), metal roofs, stucco and masonry parapet walls. For use on a properly drained roof. Coverage: On smooth surfaces, approximately 2 gallon per 100 sq. ft. (applied in 2 coats of 1 gallon per 100 sq. ft). (For 20 dry mils, apply in 2 coats of 1-1/4 gallon per 100 sq. ft.). On mineral surfaces, approximately 2 to 3 gallon per 100 sq. ft., depending on porosity and roughness of surface (applied in 2 coats of 1 to 1-1/2 gallon per 100 sq. ft.). 10 year warranty.
$28.99

Henry Enviro-White 5 Gal. Acrylic Elastomeric Roof Coating

SKU: 109796
UPC: 00081725054455
Enviro White Premium White Roof Coating is a premium, high-solids, white elastomeric roof coating formulated with acrylic polymers, resins, fillers, and titanium dioxide pigments. DPR (dirt pick-up resistant) technology prevents dirt and dust build-up, keeping your roof whiter and more reflective longer. This maximizes your energy savings over time. The elongation, peel strength, and solar reflectance values of this coating offer weather protection, high solar reflectivity, and superior longevity when compared to economy grade reflective roof coatings. Intact cured coating forms a permeable membrane which prevents liquid infiltration, but allows moisture vapor to vent, or breathe, out of underlying substrate. No primer needed on most new roofs or roofs in excellent condition. Older roofs in fair condition may need primer. For use on a properly drained roof. On smooth surfaces, approximately 2 gallon per 100 sq. ft. On mineral surfaces approximately 2 to 3 gallons per 100 sq. ft. Color: White. Meets the ENERGY STAR guidelines for energy efficiency. 12 year limited warranty.
$119.99

Henry Dura-Brite 5 Gal. White Acrylic Elastomeric Roof Coating

SKU: 123927
UPC: 00081725054738
A premium, high solids, white elastomeric roof coating. The elongation, peel strength and solar reflectance values of this coating offer weather protection, high solar reflectivity and superior longevity when compared to economy grade reflective roof coatings. Cured coating forms a permeable membrane which prevents liquid infiltration, but allows moisture vapor to vent, or breathe out of underlying substrate. Ponding water-resistant. Energy efficient - releases 91% of the sun's heat (thermal emittance). Elastomeric - expands and contracts without cracking. No primer needed on new roofs or roofs in excellent condition. Older roofs in fair condition may need primer. White roof coating offers a premium system which can be used over: Well adhered, weathered, previously coated white or aluminum roof surfaces, mineral surface cap sheet (conventional, SBS, or APP), smooth surface BUR, SBS, and APP roofs (require a base coat of Henry Asphalt Emulsion), metal roofs, stucco and masonry parapet walls. For use on a properly drained roof. Coverage: On smooth surfaces, approximately 2 gallon per 100 sq. ft. (applied in 2 coats of 1 gallon per 100 sq. ft). (For 20 dry mils, apply in 2 coats of 1-1/4 gallon per 100 sq. ft.). On mineral surfaces, approximately 2 to 3 gallon per 100 sq. ft., depending on porosity and roughness of surface (applied in 2 coats of 1 to 1-1/2 gallon per 100 sq. ft.). 10 year warranty.
$97.99

Henry Aqua-Brite 1 Gal. Fibered Aluminum Roof Coating

SKU: 100152
UPC: 00081725071711
Professional product designed to add years of service and reflectivity to a roof surface. Combination of premium aluminum flakes suspended in emulsified asphalt. Helps reduce interior temperature and protects the roof and roofing membrane by reducing heat absorption, asphalt oxidation, and rapid thermal dimensional changes. Designed to be used by professional contractors only and can be used as a reflective coating for smooth surfaced built-up roofing and Modified Bitumen Membranes. The following types of roof systems can also be coated when they are properly prepared: Smooth surfaced asphalt roofing, weathered asphalt built-up roofing, weathered galvanized metal. Coverage: 1.5 gallon per 100 sq. ft. on smooth surfaces. Coverage varies with surface texture. Do not apply unless temperatures are at least 50 deg. F. and rising. Do not apply if rain or frost is forecast within 24 hours. All equipment can be cleaned up with water and heavy-duty detergent. 7 year limited warranty.
$33.99

Henry Aqua-Brite 5 Gal. Fibered Aluminum Roof Coating

SKU: 100143
UPC: 00081725072251
Professional product designed to add years of service and reflectivity to a roof surface. Combination of premium aluminum flakes suspended in emulsified asphalt. Helps reduce interior temperature and protects the roof and roofing membrane by reducing heat absorption, asphalt oxidation, and rapid thermal dimensional changes. Designed to be used by professional contractors only and can be used as a reflective coating for smooth surfaced built-up roofing and Modified Bitumen Membranes. The following types of roof systems can also be coated when they are properly prepared: Smooth surfaced asphalt roofing, weathered asphalt built-up roofing, weathered galvanized metal. Coverage: 1.5 gallon per 100 sq. ft. on smooth surfaces. Coverage varies with surface texture. Do not apply unless temperatures are at least 50 deg. F. and rising. Do not apply if rain or frost is forecast within 24 hours. All equipment can be cleaned up with water and heavy-duty detergent. 7 year limited warranty.
$94.99

Henry Tropi-Cool 1 Gal. Silicone Roof Coating

SKU: 100503
UPC: 00081725251106
Henry 887HS Tropi-Cool 100% silicone white roof coating is a moisture cure coating designed to reflect the sun's heat and UV (ultraviolet) rays as well as protect many types of roofs. While suitable for use in all climates, the 100% silicone chemistry is especially suited for extreme tropical environments, which are exposed to some of the hottest and wettest weather with intense UV exposure. It is specially designed to maintain maximum reflectivity of heat and UV rays as it ages. Its moisture cure chemistry creates a very aggressive chemical bond with the roof, which provides permanent resistance to ponding water, extreme durability, and superior capabilities of sealing and protection. Features: Lifetime warranty, saves energy by reflecting heat, excellent adhesion and flexibility, long-lasting waterproof seal, 1 coat application, and rain-safe in 1 hour. VOC compliant, solvent-free. Wide application temperature range from 35 F (degrees Fahrenheit) to 120 F. Mold and mildew resistant. Easy to apply by spray, roller, or brush.
$62.99

Henry 1 Gal. Fibered Aluminum Roof Coating

SKU: 102481
UPC: 00081725555402
An ultra-premium fibered aluminum coating that forms a shiny, tough, reflective surface. It can decrease heating and air conditioning costs and keeps the inside temperature of a building up to 20 deg. F. cooler in summer. Not for sale in Southern California . Use as a surface coat for mineral surface cap sheet, smooth built-up, ModifiedPLUS SBS or APP assemblies, metal roofs, masonry surfaces previously coated with asphalt roof coating, or asphalt primer and weathered asphalt mastic. Mechanically mix thoroughly before and during application. Apply to a dry surface. Application to a damp surface will cause this product to appear brown. Do not apply if there is a threat of rain or dew within 24 to 48 hours. Clean up with kerosene, paint thinner, or mineral spirits. Coverage: 2.0 gal/100 sq. ft. - mineral surfaced cap sheets; 1.25 gal/100 sq. ft. - metal surfaces; 1.5 gal/100 sq. ft. - smooth emulsion surfaces. 7 year extended warranty is in addition to the limited warranty.
$22.49

Henry 5 Gal. Fibered Aluminum Roof Coating

SKU: 102506
UPC: 00081725555709
An ultra-premium fibered aluminum coating that forms a shiny, tough, reflective surface. It can decrease heating and air conditioning costs and keeps the inside temperature of a building up to 20 deg. F. cooler in summer. Not for sale in Southern California . Use as a surface coat for mineral surface cap sheet, smooth built-up, ModifiedPLUS SBS or APP assemblies, metal roofs, masonry surfaces previously coated with asphalt roof coating, or asphalt primer and weathered asphalt mastic. Mechanically mix thoroughly before and during application. Apply to a dry surface. Application to a damp surface will cause this product to appear brown. Do not apply if there is a threat of rain or dew within 24 to 48 hours. Clean up with kerosene, paint thinner, or mineral spirits. Coverage: 2.0 gal/100 sq. ft. - mineral surfaced cap sheets; 1.25 gal/100 sq. ft. - metal surfaces; 1.5 gal/100 sq. ft. - smooth emulsion surfaces. 7 year extended warranty is in addition to the limited warranty.
$84.99

Henry Elastomulsion 787 5 Gal. Waterproofing & Dampproofing

SKU: 102472
UPC: 00081725787704
Seamless rubberized asphalt membrane. Use in waterproofing or dampproofing concrete and masonry surfaces above and below grade. Excellent adhesion to most construction surfaces such as: Concrete, brick, stone, wood, or metal. Retains flexibility in wide temperature range. Cold applied by trowel, brush, or spray; requires no special equipment such as kettles. VOC compliant. Nonflammable.
$75.99

Gaco Western 2 Gal. Silicone Elastomeric Roof Coating

SKU: 772375
UPC: 00685055410372
High quality, single component elastomeric coating provides a long lasting waterproof membrane on a flat or sloped roof. The coating is made from silicone, allowing for superior protection against permanent ponding water, UV rays, and temperature extremes. It can be rained on after 2 hours and will not wash off the roof. Adheres directly to the substrate and does not require a primer. Remains permanently flexible. Application range from 32 degree F. to 120 degree F. Superior solvent and chemical resistance. Bonds to aged asphalt, aged EPDM, aged TPO/CPA, built-up, cap sheet, composite, concrete, fiberglass, metal, modified bitumen, torchdown, sprayed polyurethane foam, and most existing coatings on flat or sloped roofs. Use to protect large and small buildings, homes, garages, patio covers, sheds, barns, mobile homes, RVs, and more.
$79.99
All Categories